TECNOCOAT SERIES
TECNOCOAT P –2049
Universal pure polyurea excellent for any application. 100% Pure polyurea membrane
TECNOCOAT P-2049 EL
More Elastic, 100% Pure expandable polyurea membrane (elongation >600%)
TECNOCOAT P-2049 LV
- Low viscosity and More fluid
- Polyurea membrane 100% pure and low viscosity
TECNOCOAT P-2049 AS
- Antistatic
- 100% pure polyurea membrane with antiestatic properties
TECNOCOAT P-2049 EX
- Expansive
- Expansive 100% pure poliurea
- TECNOCOAT P-2049 EX has been developed as a single coating and is suitable for waterproofing, sealing, thermal insulation and protection, especially on uneven surfaces. It forms a continuous protective layer without joints or overlaps. The applied material expands 5 to 7 times its initial thickness. Only 1 kg of material obtains a membrane with 6 mm of thickness.
TECNOCOAT P-2049 HR
- High resistant
- 100% pure polyurea membrane of high resistant
- This pure polyurea is especially developed for applications where extreme resistance is
required as it has a Shore A hardness of about 100.
TECNOCOAT CP- 2049
- TECNOCOAT CP-2049 is a bi-component polyurea for manual application using a roller, specially recommended for renovation work on surfaces such as roofing which equire a quality membrane finish but are difficult to access with projection equipment. The membrane is esistant to pedestrian traffic.
- Expansive 100% pure poliurea
- TECNOCOAT P-2049 EX has been developed as a single coating and is suitable for waterproofing, sealing, thermal insulation and protection, especially on uneven surfaces. It forms a continuous protective layer without joints or overlaps. The applied material expands 5 to 7 times its initial thickness. Only 1 kg of material obtains a membrane with 6 mm of thickness.
- 100% pure polyurea is a cold applied membrane, which should be applied by hand, and is specifically designed for carrying out small repairs to any membrane in the TECNOCOAT product range in areas that cannot be accessed using spray equipment. Its drying time is around 50 minutes, which gives it self-levelling properties which result in an extremely smooth surface. It is sold in small containers.
DESMOPOL SERIES
DESMOPOL 1K PU
- Polyurethane membrane
- A Mono-component polyurethane elastomer which produces a continuous aromatic
membrane, with elastic properties, fully adherent to the surface and 100% watertight. It is
ideal for application to all types of surfaces in both new build and rehabilitation projects.
DESMOPOL Q 2K PU
- Liquid system for Flat roofs and balconies Waterproofing
- The DESMOPOL-Q is two component specially formulated for all types of surfaces for new construction and rehabilitation purposes.
DESMOPOL CB
- Bitumen membrane / polyurethane
with pitch bitumen, which once catalyzed forms a continuous elastic membrane, without any joints, overlapping or any integrated mesh needs. Its properties make it an excellent choice for achieving air-tightness and perfect waterproofing on a multitude of surfaces and substrates.
DESMOPOL DW
- Polyurethane membrane designed and approved for contact with water destined for human consumption
- DESMOPOL DW is a two-component liquid made up of 100% solids aromatic polyurethane, which once catalyzed forms a continuous elastic membrane, without any joints, overlapping or any integrated mesh needs. Its properties make it an excellent choice for achieving air-tightness and perfect waterproofing in potable water contact.
DESMOPOL T
- Transparent polyurethane aliphatic membrane
- DESMOPOL T is a transparent and aliphatic liquid polyurethane material, forming a continuous and elastic membrane, without joins or overlaps, providing a perfectly waterproof and watertight finish.
TECNOFOAM SERIES
Available in two blowing agent
HFO GAS AS BLOWING AGENT
TECNOFOAM HFO use an accepted by the European Regulation gas as a blown agent to forms the final solid product. It has a high close cell content and a good lambda factor (thermal conductivity). Several densities are offering to be applied.
- High initial k-factor.
- It doesn’t emit fluorinated gases.
- High dimensional stability.
- Can be used in the same way as the existing non permitted gas(365,141b, HFC)
H2OWATER AS BLOWING AGENT
TECNOFOAM H2O is our range of polyurethane foams that uses water as a blown agent, so it is according to the European regulation regarding the range of densities available is designed to cover all of your specific
requirements.
- Longer shelf live (4-5 months).
- High dimensional stability..
- Smooth external surface finishing
- Production cost is lower.
- No gases used. Could be considered “green product”.
- Not affected by future laws as regard gas emissions.
TECNOFOAM G-2025
25 kg/m3
- Wall cavities, inverted roofs, ceiling
Assemblies, ventilated facades.
Main properties:
- High expansion(4 cms in one coat)
- Low consumption
TECNOFOAM G-2008
12 kg/m3
- Wall cavities, roofs and ceiling
Assemblies, attics and crawl spaces.
Main properties:
- High expansion( 10-11 cms in one coat)
- Low consumption
- Capacity to fill spaces
TECNOFOAM G-2035
35 kg/m3
- Wall cavities, inverted roofs, ceiling
Assemblies, ventilated facades etc.
Main properties:
- The most used foam in southern Europe
TECNOFOAM G-2035
TECNOFOAM G-2035 HFO
35 kg/m3
- Wall cavities, inverted roofs, ceiling Assemblies, ventilated facades etc.
Main properties:
- The most used foam in southern Europe
TECNOFOAM G-2040
TECNOFOAM G-2040 HFO
40 kg/m3
- Roofing, balconies and terraces with Pedestrian traffic
Main properties:
- High density
- Used on indoor for heating flooring
- Used on outdoor roofs, always protected against water and humidity
TECNOFOAM G-2040 FR
- Insulation with specific fire resistant
requirements
TECNOFOAM G-2050
50 kg/m3
- Roofing and terraces or public areas with Intense traffic(vehicles).
Main properties:
- High density
- Used on outdoor roofs
TECNOFOAM G-2060 HFO
60 kg/m3
- Roofing and terraces with pedestrian
And intense traffic.
Main properties:
- High density
- Available to be protected using Tecnocoat range of polyureas
TECNOFLOOR SERIES
TECNOFLOOR T-3020
- 100% solid epoxy coating
- TECNOFLOOR T-3020 is a pigmented and fluid epoxy coating, with a 100% mechanical and chemical resistance for the covering of concrete floors and paving. It is specially designed as a finish for industrial concrete flooring requiring high performance.
TECNOFLOOR T-3040
- Water based epoxy coating
- TECNOFLOOR Tw-3040 is a pigmented and fluid epoxy coating, water-based and highly resistant to chemical and mechanical exposure. It is specially designed for application in garages, car parks, areas of vehicle traffic and flooring with demanding requirements in terms of decontamination and cleaning, industrial chemicals and food product activity.
TECNOFLOOR PU-3010
- Polyurethane based covering
- TECNOFLOOR PU-3010 is a bright and fluid pigmented coating, with a polyurethane base for the coating of concrete floors. It is specially designed for application in garages, car parks, areas of vehicle traffic and flooring with demanding requirements in terms of zecontamination and cleaning, industrial chemicals and food product activity.
TECNOFLOOR PU-3060
- 100% solid polyurethane based
Covering - TECNOFLOOR PU-3060 is a bright and fluid pigmented coating, with a polyurethane base for the coating of concrete floors. It is specially designed as a protective coating and finish for concrete, industrial flooring and areas of intense traffic.